Datasets:
Dataset Viewer
id
stringlengths 11
11
| images
listlengths 1
4
| conversations
listlengths 2
2
|
|---|---|---|
Shaft_03512
|
[
"images/Shaft_03512.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø56.6 mm and length at least 129.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.6 mm over length 49.4 mm (from Z=0.0 to Z=49.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.4 mm over length 34.2 mm (from Z=0.0 to Z=74.8).\n9. Finish turn diameter Ø30.0 mm over length 40.6 mm (from Z=0.0 to Z=40.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03270
|
[
"images/Shaft_03270.png",
"detail_png/Shaft_03270_length.png",
"detail_png/Shaft_03270_diam.png",
"detail_png/Shaft_03270_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø69.4 mm and length at least 294.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.4 mm over length 51.1 mm (from Z=0.0 to Z=51.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø47.6 mm over length 48.7 mm (from Z=0.0 to Z=238.6).\n10. Finish turn diameter Ø38.7 mm over length 114.7 mm (from Z=0.0 to Z=189.9).\n11. Finish turn diameter Ø30.0 mm over length 75.2 mm (from Z=0.0 to Z=75.2).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03606
|
[
"images/Shaft_03606.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø38.2 mm and length at least 282.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø36.2 mm over length 106.0 mm (from Z=0.0 to Z=106.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø36.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 171.7 mm (from Z=0.0 to Z=171.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01365
|
[
"images/Shaft_01365.png",
"detail_png/Shaft_01365_length.png",
"detail_png/Shaft_01365_diam.png",
"detail_png/Shaft_01365_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø71.4 mm and length at least 120.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.4 mm over length 46.5 mm (from Z=0.0 to Z=46.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.2 mm over length 25.9 mm (from Z=0.0 to Z=69.4).\n9. Finish turn diameter Ø51.8 mm over length 43.5 mm (from Z=0.0 to Z=43.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04616
|
[
"images/Shaft_04616.png",
"detail_png/Shaft_04616_length.png",
"detail_png/Shaft_04616_diam.png",
"detail_png/Shaft_04616_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 125.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 96.6 mm (from Z=0.0 to Z=96.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.5 mm over length 23.6 mm (from Z=0.0 to Z=23.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00159
|
[
"images/Shaft_00159.png",
"detail_png/Shaft_00159_length.png",
"detail_png/Shaft_00159_diam.png",
"detail_png/Shaft_00159_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø72.2 mm and length at least 211.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.2 mm over length 33.7 mm (from Z=0.0 to Z=33.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø53.7 mm over length 46.2 mm (from Z=0.0 to Z=172.4).\n10. Finish turn diameter Ø46.3 mm over length 52.5 mm (from Z=0.0 to Z=126.2).\n11. Finish turn diameter Ø40.7 mm over length 16.6 mm (from Z=0.0 to Z=73.7).\n12. Finish turn diameter Ø30.0 mm over length 57.1 mm (from Z=0.0 to Z=57.1).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00425
|
[
"images/Shaft_00425.png",
"detail_png/Shaft_00425_length.png",
"detail_png/Shaft_00425_diam.png",
"detail_png/Shaft_00425_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø48.8 mm and length at least 205.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø46.8 mm over length 53.7 mm (from Z=0.0 to Z=53.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø46.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.8 mm over length 49.4 mm (from Z=0.0 to Z=146.4).\n10. Finish turn diameter Ø30.0 mm over length 97.0 mm (from Z=0.0 to Z=97.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01613
|
[
"images/Shaft_01613.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø69.5 mm and length at least 208.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.5 mm over length 29.7 mm (from Z=0.0 to Z=29.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.3 mm over length 25.2 mm (from Z=0.0 to Z=173.3).\n10. Finish turn diameter Ø48.8 mm over length 69.7 mm (from Z=0.0 to Z=148.1).\n11. Finish turn diameter Ø39.8 mm over length 24.4 mm (from Z=0.0 to Z=78.4).\n12. Finish turn diameter Ø31.0 mm over length 54.0 mm (from Z=0.0 to Z=54.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04676
|
[
"images/Shaft_04676.png",
"detail_png/Shaft_04676_length.png",
"detail_png/Shaft_04676_diam.png",
"detail_png/Shaft_04676_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø52.0 mm and length at least 136.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.0 mm over length 29.9 mm (from Z=0.0 to Z=29.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø37.9 mm over length 32.6 mm (from Z=0.0 to Z=101.3).\n9. Finish turn diameter Ø30.0 mm over length 68.7 mm (from Z=0.0 to Z=68.7).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02867
|
[
"images/Shaft_02867.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 216.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 166.5 mm (from Z=0.0 to Z=166.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø29.9 mm over length 44.5 mm (from Z=0.0 to Z=44.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03967
|
[
"images/Shaft_03967.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 252.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 159.6 mm (from Z=0.0 to Z=159.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.7 mm over length 87.8 mm (from Z=0.0 to Z=87.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03235
|
[
"images/Shaft_03235.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.5 mm and length at least 197.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.5 mm over length 30.3 mm (from Z=0.0 to Z=30.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 162.5 mm (from Z=0.0 to Z=162.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04971
|
[
"images/Shaft_04971.png",
"detail_png/Shaft_04971_length.png",
"detail_png/Shaft_04971_diam.png",
"detail_png/Shaft_04971_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 252.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 182.6 mm (from Z=0.0 to Z=182.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø28.2 mm over length 65.1 mm (from Z=0.0 to Z=65.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01518
|
[
"images/Shaft_01518.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø55.4 mm and length at least 263.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 38.0 mm (from Z=0.0 to Z=38.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø49.3 mm over length 124.8 mm (from Z=0.0 to Z=220.0).\n10. Finish turn diameter Ø41.3 mm over length 95.2 mm (from Z=0.0 to Z=95.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00105
|
[
"images/Shaft_00105.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø32.0 mm and length at least 151.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 111.4 mm (from Z=0.0 to Z=111.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø22.6 mm over length 34.9 mm (from Z=0.0 to Z=34.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04122
|
[
"images/Shaft_04122.png",
"detail_png/Shaft_04122_length.png",
"detail_png/Shaft_04122_diam.png",
"detail_png/Shaft_04122_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø36.1 mm and length at least 310.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.1 mm over length 107.8 mm (from Z=0.0 to Z=107.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 197.3 mm (from Z=0.0 to Z=197.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03436
|
[
"images/Shaft_03436.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø71.2 mm and length at least 66.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø69.2 mm over length 10.7 mm (from Z=0.0 to Z=10.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø69.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.5 mm over length 21.2 mm (from Z=0.0 to Z=50.8).\n9. Finish turn diameter Ø36.5 mm over length 7.8 mm (from Z=0.0 to Z=29.6).\n10. Finish turn diameter Ø32.6 mm over length 21.8 mm (from Z=0.0 to Z=21.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03182
|
[
"images/Shaft_03182.png",
"detail_png/Shaft_03182_length.png",
"detail_png/Shaft_03182_diam.png",
"detail_png/Shaft_03182_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø37.5 mm and length at least 108.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.5 mm over length 13.9 mm (from Z=0.0 to Z=13.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 89.4 mm (from Z=0.0 to Z=89.4).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00100
|
[
"images/Shaft_00100.png",
"detail_png/Shaft_00100_length.png",
"detail_png/Shaft_00100_diam.png",
"detail_png/Shaft_00100_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø41.6 mm and length at least 189.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.6 mm over length 68.2 mm (from Z=0.0 to Z=68.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 116.2 mm (from Z=0.0 to Z=116.2).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03909
|
[
"images/Shaft_03909.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.5 mm and length at least 307.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.5 mm over length 142.1 mm (from Z=0.0 to Z=142.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 159.9 mm (from Z=0.0 to Z=159.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03496
|
[
"images/Shaft_03496.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø58.3 mm and length at least 202.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø56.3 mm over length 99.7 mm (from Z=0.0 to Z=99.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø56.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.1 mm over length 44.8 mm (from Z=0.0 to Z=98.2).\n10. Finish turn diameter Ø38.9 mm over length 36.6 mm (from Z=0.0 to Z=53.4).\n11. Finish turn diameter Ø35.5 mm over length 16.8 mm (from Z=0.0 to Z=16.8).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_00612
|
[
"images/Shaft_00612.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø81.5 mm and length at least 153.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø79.5 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø79.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø76.4 mm over length 41.5 mm (from Z=0.0 to Z=127.8).\n9. Finish turn diameter Ø68.8 mm over length 10.8 mm (from Z=0.0 to Z=86.3).\n10. Finish turn diameter Ø62.4 mm over length 29.5 mm (from Z=0.0 to Z=75.5).\n11. Finish turn diameter Ø52.3 mm over length 34.3 mm (from Z=0.0 to Z=46.0).\n12. Finish turn diameter Ø33.4 mm over length 11.7 mm (from Z=0.0 to Z=11.7).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_00544
|
[
"images/Shaft_00544.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø72.4 mm and length at least 285.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.4 mm over length 71.5 mm (from Z=0.0 to Z=71.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø61.2 mm over length 92.4 mm (from Z=0.0 to Z=209.1).\n10. Finish turn diameter Ø48.1 mm over length 116.7 mm (from Z=0.0 to Z=116.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00722
|
[
"images/Shaft_00722.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø67.3 mm and length at least 91.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.3 mm over length 27.2 mm (from Z=0.0 to Z=27.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.9 mm over length 5.0 mm (from Z=0.0 to Z=59.5).\n9. Finish turn diameter Ø41.6 mm over length 17.7 mm (from Z=0.0 to Z=54.5).\n10. Finish turn diameter Ø30.0 mm over length 36.8 mm (from Z=0.0 to Z=36.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02146
|
[
"images/Shaft_02146.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø44.6 mm and length at least 67.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø42.6 mm over length 16.0 mm (from Z=0.0 to Z=16.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø42.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 46.9 mm (from Z=0.0 to Z=46.9).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_04136
|
[
"images/Shaft_04136.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø36.1 mm and length at least 106.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.1 mm over length 7.3 mm (from Z=0.0 to Z=7.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 94.1 mm (from Z=0.0 to Z=94.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01003
|
[
"images/Shaft_01003.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø75.5 mm and length at least 81.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.5 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø54.1 mm over length 14.8 mm (from Z=0.0 to Z=57.6).\n9. Finish turn diameter Ø43.1 mm over length 19.2 mm (from Z=0.0 to Z=42.8).\n10. Finish turn diameter Ø36.0 mm over length 6.1 mm (from Z=0.0 to Z=23.6).\n11. Finish turn diameter Ø30.0 mm over length 17.5 mm (from Z=0.0 to Z=17.5).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02054
|
[
"images/Shaft_02054.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø53.7 mm and length at least 189.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.7 mm over length 78.4 mm (from Z=0.0 to Z=78.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.5 mm over length 89.0 mm (from Z=0.0 to Z=105.8).\n9. Finish turn diameter Ø30.0 mm over length 16.8 mm (from Z=0.0 to Z=16.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01658
|
[
"images/Shaft_01658.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø77.8 mm and length at least 272.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.8 mm over length 70.8 mm (from Z=0.0 to Z=70.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø68.2 mm over length 55.2 mm (from Z=0.0 to Z=196.2).\n10. Finish turn diameter Ø65.2 mm over length 84.6 mm (from Z=0.0 to Z=141.0).\n11. Finish turn diameter Ø46.8 mm over length 44.9 mm (from Z=0.0 to Z=56.4).\n12. Finish turn diameter Ø33.0 mm over length 11.5 mm (from Z=0.0 to Z=11.5).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04172
|
[
"images/Shaft_04172.png",
"detail_png/Shaft_04172_length.png",
"detail_png/Shaft_04172_diam.png",
"detail_png/Shaft_04172_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø73.8 mm and length at least 244.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.8 mm over length 57.6 mm (from Z=0.0 to Z=57.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø64.7 mm over length 65.6 mm (from Z=0.0 to Z=181.8).\n10. Finish turn diameter Ø51.5 mm over length 40.4 mm (from Z=0.0 to Z=116.2).\n11. Finish turn diameter Ø48.4 mm over length 31.2 mm (from Z=0.0 to Z=75.8).\n12. Finish turn diameter Ø33.5 mm over length 44.6 mm (from Z=0.0 to Z=44.6).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_03451
|
[
"images/Shaft_03451.png",
"detail_png/Shaft_03451_length.png",
"detail_png/Shaft_03451_diam.png",
"detail_png/Shaft_03451_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø53.7 mm and length at least 135.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.7 mm over length 14.1 mm (from Z=0.0 to Z=14.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.6 mm over length 18.4 mm (from Z=0.0 to Z=116.1).\n10. Finish turn diameter Ø30.0 mm over length 97.7 mm (from Z=0.0 to Z=97.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02755
|
[
"images/Shaft_02755.png",
"detail_png/Shaft_02755_length.png",
"detail_png/Shaft_02755_diam.png",
"detail_png/Shaft_02755_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø43.9 mm and length at least 128.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.9 mm over length 61.2 mm (from Z=0.0 to Z=61.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 62.3 mm (from Z=0.0 to Z=62.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_00277
|
[
"images/Shaft_00277.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.5 mm and length at least 79.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.5 mm over length 27.3 mm (from Z=0.0 to Z=27.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø65.1 mm over length 19.2 mm (from Z=0.0 to Z=46.9).\n9. Finish turn diameter Ø61.5 mm over length 6.3 mm (from Z=0.0 to Z=27.7).\n10. Finish turn diameter Ø54.6 mm over length 5.0 mm (from Z=0.0 to Z=21.4).\n11. Finish turn diameter Ø40.5 mm over length 16.4 mm (from Z=0.0 to Z=16.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02568
|
[
"images/Shaft_02568.png",
"detail_png/Shaft_02568_length.png",
"detail_png/Shaft_02568_diam.png",
"detail_png/Shaft_02568_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø46.0 mm and length at least 254.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.0 mm over length 39.6 mm (from Z=0.0 to Z=39.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.5 mm over length 47.6 mm (from Z=0.0 to Z=209.8).\n10. Finish turn diameter Ø30.0 mm over length 162.2 mm (from Z=0.0 to Z=162.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02887
|
[
"images/Shaft_02887.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø77.1 mm and length at least 157.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.1 mm over length 38.4 mm (from Z=0.0 to Z=38.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø56.4 mm over length 30.8 mm (from Z=0.0 to Z=113.7).\n9. Finish turn diameter Ø44.2 mm over length 22.6 mm (from Z=0.0 to Z=82.9).\n10. Finish turn diameter Ø30.0 mm over length 60.3 mm (from Z=0.0 to Z=60.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01607
|
[
"images/Shaft_01607.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø72.6 mm and length at least 214.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø70.6 mm over length 32.2 mm (from Z=0.0 to Z=32.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø70.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.6 mm over length 82.8 mm (from Z=0.0 to Z=177.1).\n10. Finish turn diameter Ø45.2 mm over length 94.3 mm (from Z=0.0 to Z=94.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00785
|
[
"images/Shaft_00785.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø55.4 mm and length at least 316.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 48.1 mm (from Z=0.0 to Z=48.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.5 mm over length 17.3 mm (from Z=0.0 to Z=263.2).\n10. Finish turn diameter Ø33.4 mm over length 41.8 mm (from Z=0.0 to Z=245.9).\n11. Finish turn diameter Ø30.0 mm over length 204.1 mm (from Z=0.0 to Z=204.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03684
|
[
"images/Shaft_03684.png",
"detail_png/Shaft_03684_length.png",
"detail_png/Shaft_03684_diam.png",
"detail_png/Shaft_03684_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø37.4 mm and length at least 196.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.4 mm over length 21.3 mm (from Z=0.0 to Z=21.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 169.9 mm (from Z=0.0 to Z=169.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03892
|
[
"images/Shaft_03892.png",
"detail_png/Shaft_03892_length.png",
"detail_png/Shaft_03892_diam.png",
"detail_png/Shaft_03892_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø49.9 mm and length at least 148.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.9 mm over length 32.6 mm (from Z=0.0 to Z=32.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.0 mm over length 16.6 mm (from Z=0.0 to Z=110.6).\n9. Finish turn diameter Ø33.8 mm over length 32.3 mm (from Z=0.0 to Z=94.0).\n10. Finish turn diameter Ø30.0 mm over length 61.7 mm (from Z=0.0 to Z=61.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02710
|
[
"images/Shaft_02710.png",
"detail_png/Shaft_02710_length.png",
"detail_png/Shaft_02710_diam.png",
"detail_png/Shaft_02710_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø55.2 mm and length at least 262.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.2 mm over length 59.7 mm (from Z=0.0 to Z=59.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.5 mm over length 92.6 mm (from Z=0.0 to Z=197.3).\n10. Finish turn diameter Ø30.0 mm over length 104.7 mm (from Z=0.0 to Z=104.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03010
|
[
"images/Shaft_03010.png",
"detail_png/Shaft_03010_length.png",
"detail_png/Shaft_03010_diam.png",
"detail_png/Shaft_03010_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø54.5 mm and length at least 152.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.5 mm over length 34.1 mm (from Z=0.0 to Z=34.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø35.4 mm over length 30.5 mm (from Z=0.0 to Z=113.6).\n9. Finish turn diameter Ø31.5 mm over length 5.0 mm (from Z=0.0 to Z=83.1).\n10. Finish turn diameter Ø30.0 mm over length 78.1 mm (from Z=0.0 to Z=78.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01120
|
[
"images/Shaft_01120.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø53.9 mm and length at least 289.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø51.9 mm over length 37.8 mm (from Z=0.0 to Z=37.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø51.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.8 mm over length 21.0 mm (from Z=0.0 to Z=246.2).\n10. Finish turn diameter Ø39.7 mm over length 45.9 mm (from Z=0.0 to Z=225.2).\n11. Finish turn diameter Ø30.0 mm over length 179.3 mm (from Z=0.0 to Z=179.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04383
|
[
"images/Shaft_04383.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø79.0 mm and length at least 215.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.0 mm over length 21.2 mm (from Z=0.0 to Z=21.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.7 mm over length 53.9 mm (from Z=0.0 to Z=189.7).\n10. Finish turn diameter Ø49.0 mm over length 18.1 mm (from Z=0.0 to Z=135.8).\n11. Finish turn diameter Ø39.6 mm over length 42.7 mm (from Z=0.0 to Z=117.7).\n12. Finish turn diameter Ø30.0 mm over length 75.0 mm (from Z=0.0 to Z=75.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04945
|
[
"images/Shaft_04945.png",
"detail_png/Shaft_04945_length.png",
"detail_png/Shaft_04945_diam.png",
"detail_png/Shaft_04945_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø80.3 mm and length at least 126.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.3 mm over length 61.5 mm (from Z=0.0 to Z=61.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø75.2 mm over length 49.0 mm (from Z=0.0 to Z=59.8).\n9. Finish turn diameter Ø69.4 mm over length 10.8 mm (from Z=0.0 to Z=10.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03148
|
[
"images/Shaft_03148.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø40.8 mm and length at least 272.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.8 mm over length 47.2 mm (from Z=0.0 to Z=47.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.9 mm over length 22.1 mm (from Z=0.0 to Z=220.7).\n10. Finish turn diameter Ø30.0 mm over length 198.6 mm (from Z=0.0 to Z=198.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01468
|
[
"images/Shaft_01468.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 157.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 109.0 mm (from Z=0.0 to Z=109.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.6 mm over length 43.1 mm (from Z=0.0 to Z=43.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03828
|
[
"images/Shaft_03828.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø77.6 mm and length at least 165.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.6 mm over length 42.0 mm (from Z=0.0 to Z=42.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø61.1 mm over length 58.9 mm (from Z=0.0 to Z=118.9).\n9. Finish turn diameter Ø55.3 mm over length 60.0 mm (from Z=0.0 to Z=60.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03156
|
[
"images/Shaft_03156.png",
"detail_png/Shaft_03156_length.png",
"detail_png/Shaft_03156_diam.png",
"detail_png/Shaft_03156_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø41.9 mm and length at least 285.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.9 mm over length 113.4 mm (from Z=0.0 to Z=113.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø35.6 mm over length 10.3 mm (from Z=0.0 to Z=166.6).\n10. Finish turn diameter Ø30.0 mm over length 156.3 mm (from Z=0.0 to Z=156.3).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01316
|
[
"images/Shaft_01316.png",
"detail_png/Shaft_01316_length.png",
"detail_png/Shaft_01316_diam.png",
"detail_png/Shaft_01316_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø51.0 mm and length at least 281.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø49.0 mm over length 32.6 mm (from Z=0.0 to Z=32.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø49.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø43.6 mm over length 39.4 mm (from Z=0.0 to Z=243.8).\n10. Finish turn diameter Ø39.4 mm over length 53.1 mm (from Z=0.0 to Z=204.4).\n11. Finish turn diameter Ø30.0 mm over length 151.3 mm (from Z=0.0 to Z=151.3).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04356
|
[
"images/Shaft_04356.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø55.4 mm and length at least 307.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.4 mm over length 26.2 mm (from Z=0.0 to Z=26.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø44.9 mm over length 47.1 mm (from Z=0.0 to Z=276.4).\n10. Finish turn diameter Ø38.6 mm over length 39.3 mm (from Z=0.0 to Z=229.3).\n11. Finish turn diameter Ø30.0 mm over length 190.0 mm (from Z=0.0 to Z=190.0).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_02620
|
[
"images/Shaft_02620.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø73.3 mm and length at least 109.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø71.3 mm over length 21.8 mm (from Z=0.0 to Z=21.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø71.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø67.3 mm over length 9.3 mm (from Z=0.0 to Z=82.7).\n9. Finish turn diameter Ø54.8 mm over length 25.2 mm (from Z=0.0 to Z=73.4).\n10. Finish turn diameter Ø45.7 mm over length 28.1 mm (from Z=0.0 to Z=48.2).\n11. Finish turn diameter Ø41.0 mm over length 20.1 mm (from Z=0.0 to Z=20.1).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_01830
|
[
"images/Shaft_01830.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.4 mm and length at least 237.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.4 mm over length 51.2 mm (from Z=0.0 to Z=51.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.8 mm over length 50.0 mm (from Z=0.0 to Z=181.0).\n10. Finish turn diameter Ø30.0 mm over length 131.0 mm (from Z=0.0 to Z=131.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01561
|
[
"images/Shaft_01561.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø46.9 mm and length at least 309.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.9 mm over length 21.4 mm (from Z=0.0 to Z=21.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø34.5 mm over length 27.0 mm (from Z=0.0 to Z=283.2).\n10. Finish turn diameter Ø30.0 mm over length 256.2 mm (from Z=0.0 to Z=256.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03791
|
[
"images/Shaft_03791.png",
"detail_png/Shaft_03791_length.png",
"detail_png/Shaft_03791_diam.png",
"detail_png/Shaft_03791_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø46.0 mm and length at least 87.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø44.0 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø44.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø38.7 mm over length 20.9 mm (from Z=0.0 to Z=61.7).\n9. Finish turn diameter Ø34.4 mm over length 6.0 mm (from Z=0.0 to Z=40.8).\n10. Finish turn diameter Ø30.0 mm over length 34.8 mm (from Z=0.0 to Z=34.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02445
|
[
"images/Shaft_02445.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø43.2 mm and length at least 67.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø41.2 mm over length 14.8 mm (from Z=0.0 to Z=14.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø41.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.6 mm over length 22.8 mm (from Z=0.0 to Z=47.3).\n9. Finish turn diameter Ø30.5 mm over length 11.6 mm (from Z=0.0 to Z=24.5).\n10. Finish turn diameter Ø30.0 mm over length 12.9 mm (from Z=0.0 to Z=12.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02333
|
[
"images/Shaft_02333.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø64.4 mm and length at least 128.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø62.4 mm over length 40.4 mm (from Z=0.0 to Z=40.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø62.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.4 mm over length 34.8 mm (from Z=0.0 to Z=82.6).\n9. Finish turn diameter Ø39.3 mm over length 10.7 mm (from Z=0.0 to Z=47.8).\n10. Finish turn diameter Ø30.0 mm over length 37.1 mm (from Z=0.0 to Z=37.1).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01813
|
[
"images/Shaft_01813.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.8 mm and length at least 70.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.8 mm over length 17.0 mm (from Z=0.0 to Z=17.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.8 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 48.8 mm (from Z=0.0 to Z=48.8).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_04955
|
[
"images/Shaft_04955.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø35.1 mm and length at least 194.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.1 mm over length 18.4 mm (from Z=0.0 to Z=18.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 170.8 mm (from Z=0.0 to Z=170.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00798
|
[
"images/Shaft_00798.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø35.2 mm and length at least 73.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø33.2 mm over length 9.5 mm (from Z=0.0 to Z=9.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø33.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 59.1 mm (from Z=0.0 to Z=59.1).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_02292
|
[
"images/Shaft_02292.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø54.1 mm and length at least 92.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.1 mm over length 26.8 mm (from Z=0.0 to Z=26.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø42.8 mm over length 20.8 mm (from Z=0.0 to Z=61.0).\n9. Finish turn diameter Ø38.4 mm over length 30.0 mm (from Z=0.0 to Z=40.2).\n10. Finish turn diameter Ø30.0 mm over length 10.2 mm (from Z=0.0 to Z=10.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00154
|
[
"images/Shaft_00154.png",
"detail_png/Shaft_00154_length.png",
"detail_png/Shaft_00154_diam.png",
"detail_png/Shaft_00154_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø32.0 mm and length at least 257.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 167.3 mm (from Z=0.0 to Z=167.3).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø25.9 mm over length 85.3 mm (from Z=0.0 to Z=85.3).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04916
|
[
"images/Shaft_04916.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø54.0 mm and length at least 76.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø52.0 mm over length 20.5 mm (from Z=0.0 to Z=20.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø52.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø33.8 mm over length 17.4 mm (from Z=0.0 to Z=50.8).\n9. Finish turn diameter Ø30.0 mm over length 33.4 mm (from Z=0.0 to Z=33.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00157
|
[
"images/Shaft_00157.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø70.6 mm and length at least 96.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø68.6 mm over length 33.1 mm (from Z=0.0 to Z=33.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø68.6 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø48.8 mm over length 22.4 mm (from Z=0.0 to Z=58.6).\n9. Finish turn diameter Ø44.3 mm over length 13.4 mm (from Z=0.0 to Z=36.2).\n10. Finish turn diameter Ø30.0 mm over length 22.8 mm (from Z=0.0 to Z=22.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04232
|
[
"images/Shaft_04232.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø34.0 mm and length at least 217.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.0 mm over length 26.7 mm (from Z=0.0 to Z=26.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 186.1 mm (from Z=0.0 to Z=186.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01450
|
[
"images/Shaft_01450.png",
"detail_png/Shaft_01450_length.png",
"detail_png/Shaft_01450_diam.png",
"detail_png/Shaft_01450_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø52.5 mm and length at least 159.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.5 mm over length 20.1 mm (from Z=0.0 to Z=20.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø46.6 mm over length 18.8 mm (from Z=0.0 to Z=133.9).\n9. Finish turn diameter Ø35.8 mm over length 61.2 mm (from Z=0.0 to Z=115.1).\n10. Finish turn diameter Ø30.0 mm over length 53.9 mm (from Z=0.0 to Z=53.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02487
|
[
"images/Shaft_02487.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø32.0 mm and length at least 113.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 85.6 mm (from Z=0.0 to Z=85.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø21.8 mm over length 23.3 mm (from Z=0.0 to Z=23.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_04296
|
[
"images/Shaft_04296.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø37.9 mm and length at least 173.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.9 mm over length 43.9 mm (from Z=0.0 to Z=43.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø32.4 mm over length 8.6 mm (from Z=0.0 to Z=125.0).\n10. Finish turn diameter Ø30.0 mm over length 116.4 mm (from Z=0.0 to Z=116.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02342
|
[
"images/Shaft_02342.png",
"detail_png/Shaft_02342_length.png",
"detail_png/Shaft_02342_diam.png",
"detail_png/Shaft_02342_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 212.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 147.4 mm (from Z=0.0 to Z=147.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.8 mm over length 60.1 mm (from Z=0.0 to Z=60.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00339
|
[
"images/Shaft_00339.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø37.9 mm and length at least 187.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.9 mm over length 15.4 mm (from Z=0.0 to Z=15.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 166.6 mm (from Z=0.0 to Z=166.6).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04545
|
[
"images/Shaft_04545.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø76.8 mm and length at least 226.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.8 mm over length 55.8 mm (from Z=0.0 to Z=55.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø55.7 mm over length 41.2 mm (from Z=0.0 to Z=165.7).\n10. Finish turn diameter Ø40.4 mm over length 45.5 mm (from Z=0.0 to Z=124.5).\n11. Finish turn diameter Ø31.9 mm over length 59.0 mm (from Z=0.0 to Z=79.0).\n12. Finish turn diameter Ø30.0 mm over length 20.0 mm (from Z=0.0 to Z=20.0).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_04471
|
[
"images/Shaft_04471.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø78.3 mm and length at least 303.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.3 mm over length 14.6 mm (from Z=0.0 to Z=14.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.6 mm over length 89.7 mm (from Z=0.0 to Z=283.7).\n10. Finish turn diameter Ø50.8 mm over length 91.4 mm (from Z=0.0 to Z=194.0).\n11. Finish turn diameter Ø39.4 mm over length 22.7 mm (from Z=0.0 to Z=102.6).\n12. Finish turn diameter Ø33.4 mm over length 79.9 mm (from Z=0.0 to Z=79.9).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_01760
|
[
"images/Shaft_01760.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø50.8 mm and length at least 250.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø48.8 mm over length 19.1 mm (from Z=0.0 to Z=19.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø48.8 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.0 mm over length 53.6 mm (from Z=0.0 to Z=226.4).\n10. Finish turn diameter Ø30.0 mm over length 172.8 mm (from Z=0.0 to Z=172.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02160
|
[
"images/Shaft_02160.png",
"detail_png/Shaft_02160_length.png",
"detail_png/Shaft_02160_diam.png",
"detail_png/Shaft_02160_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø56.3 mm and length at least 218.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø54.3 mm over length 61.0 mm (from Z=0.0 to Z=61.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø54.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø42.1 mm over length 69.1 mm (from Z=0.0 to Z=152.1).\n10. Finish turn diameter Ø35.2 mm over length 62.1 mm (from Z=0.0 to Z=83.0).\n11. Finish turn diameter Ø31.1 mm over length 20.9 mm (from Z=0.0 to Z=20.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04674
|
[
"images/Shaft_04674.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø41.4 mm and length at least 188.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø39.4 mm over length 48.0 mm (from Z=0.0 to Z=48.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø39.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.1 mm over length 21.5 mm (from Z=0.0 to Z=135.3).\n10. Finish turn diameter Ø30.0 mm over length 113.8 mm (from Z=0.0 to Z=113.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_03707
|
[
"images/Shaft_03707.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø78.9 mm and length at least 260.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø76.9 mm over length 78.8 mm (from Z=0.0 to Z=78.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø76.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø59.2 mm over length 36.6 mm (from Z=0.0 to Z=176.3).\n10. Finish turn diameter Ø49.8 mm over length 58.7 mm (from Z=0.0 to Z=139.7).\n11. Finish turn diameter Ø32.2 mm over length 10.3 mm (from Z=0.0 to Z=81.0).\n12. Finish turn diameter Ø30.0 mm over length 70.7 mm (from Z=0.0 to Z=70.7).\n13. Break all edges (e.g., 2×45° where applicable).\n14. Remove the workpiece from the lathe."
}
] |
Shaft_03744
|
[
"images/Shaft_03744.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø39.4 mm and length at least 290.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø37.4 mm over length 46.8 mm (from Z=0.0 to Z=46.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø37.4 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.2 mm over length 53.1 mm (from Z=0.0 to Z=239.0).\n10. Finish turn diameter Ø30.0 mm over length 185.9 mm (from Z=0.0 to Z=185.9).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00326
|
[
"images/Shaft_00326.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø77.2 mm and length at least 228.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø75.2 mm over length 94.9 mm (from Z=0.0 to Z=94.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø75.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø70.5 mm over length 93.8 mm (from Z=0.0 to Z=129.0).\n10. Finish turn diameter Ø56.8 mm over length 22.3 mm (from Z=0.0 to Z=35.2).\n11. Finish turn diameter Ø51.1 mm over length 12.9 mm (from Z=0.0 to Z=12.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_04668
|
[
"images/Shaft_04668.png",
"detail_png/Shaft_04668_length.png",
"detail_png/Shaft_04668_diam.png",
"detail_png/Shaft_04668_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø67.0 mm and length at least 172.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø65.0 mm over length 63.0 mm (from Z=0.0 to Z=63.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø65.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø52.3 mm over length 94.6 mm (from Z=0.0 to Z=104.6).\n9. Finish turn diameter Ø40.9 mm over length 10.0 mm (from Z=0.0 to Z=10.0).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04102
|
[
"images/Shaft_04102.png",
"detail_png/Shaft_04102_length.png",
"detail_png/Shaft_04102_diam.png",
"detail_png/Shaft_04102_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø75.5 mm and length at least 178.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø73.5 mm over length 39.8 mm (from Z=0.0 to Z=39.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø73.5 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø55.5 mm over length 58.3 mm (from Z=0.0 to Z=133.7).\n9. Finish turn diameter Ø37.6 mm over length 53.4 mm (from Z=0.0 to Z=75.4).\n10. Finish turn diameter Ø30.0 mm over length 22.0 mm (from Z=0.0 to Z=22.0).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_02904
|
[
"images/Shaft_02904.png",
"detail_png/Shaft_02904_length.png",
"detail_png/Shaft_02904_diam.png",
"detail_png/Shaft_02904_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø32.0 mm and length at least 319.3 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 147.8 mm (from Z=0.0 to Z=147.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø27.0 mm over length 166.5 mm (from Z=0.0 to Z=166.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01377
|
[
"images/Shaft_01377.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø34.7 mm and length at least 309.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.7 mm over length 28.8 mm (from Z=0.0 to Z=28.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 275.9 mm (from Z=0.0 to Z=275.9).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02884
|
[
"images/Shaft_02884.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø36.6 mm and length at least 162.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø34.6 mm over length 27.0 mm (from Z=0.0 to Z=27.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø34.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 130.8 mm (from Z=0.0 to Z=130.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01128
|
[
"images/Shaft_01128.png",
"detail_png/Shaft_01128_length.png",
"detail_png/Shaft_01128_diam.png",
"detail_png/Shaft_01128_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø69.1 mm and length at least 225.4 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.1 mm over length 19.0 mm (from Z=0.0 to Z=19.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.1 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø58.7 mm over length 43.7 mm (from Z=0.0 to Z=201.4).\n10. Finish turn diameter Ø54.4 mm over length 14.3 mm (from Z=0.0 to Z=157.7).\n11. Finish turn diameter Ø48.1 mm over length 11.6 mm (from Z=0.0 to Z=143.4).\n12. Finish turn diameter Ø33.1 mm over length 76.0 mm (from Z=0.0 to Z=131.8).\n13. Finish turn diameter Ø30.0 mm over length 55.8 mm (from Z=0.0 to Z=55.8).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_03273
|
[
"images/Shaft_03273.png",
"detail_png/Shaft_03273_length.png",
"detail_png/Shaft_03273_diam.png",
"detail_png/Shaft_03273_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 80.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 62.8 mm (from Z=0.0 to Z=62.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø25.3 mm over length 12.2 mm (from Z=0.0 to Z=12.2).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_04303
|
[
"images/Shaft_04303.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø69.3 mm and length at least 274.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.3 mm over length 127.5 mm (from Z=0.0 to Z=127.5).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.3 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø63.6 mm over length 80.2 mm (from Z=0.0 to Z=142.3).\n10. Finish turn diameter Ø54.0 mm over length 24.7 mm (from Z=0.0 to Z=62.1).\n11. Finish turn diameter Ø35.8 mm over length 37.4 mm (from Z=0.0 to Z=37.4).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03333
|
[
"images/Shaft_03333.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø59.7 mm and length at least 313.2 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø57.7 mm over length 20.8 mm (from Z=0.0 to Z=20.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø57.7 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø52.1 mm over length 68.2 mm (from Z=0.0 to Z=287.4).\n10. Finish turn diameter Ø39.4 mm over length 95.3 mm (from Z=0.0 to Z=219.2).\n11. Finish turn diameter Ø30.0 mm over length 123.9 mm (from Z=0.0 to Z=123.9).\n12. Break all edges (e.g., 2×45° where applicable).\n13. Remove the workpiece from the lathe."
}
] |
Shaft_03413
|
[
"images/Shaft_03413.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø34.2 mm and length at least 114.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø32.2 mm over length 25.6 mm (from Z=0.0 to Z=25.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø32.2 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø30.0 mm over length 84.3 mm (from Z=0.0 to Z=84.3).\n9. Break all edges (e.g., 2×45° where applicable).\n10. Remove the workpiece from the lathe."
}
] |
Shaft_01775
|
[
"images/Shaft_01775.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø80.1 mm and length at least 108.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø78.1 mm over length 33.9 mm (from Z=0.0 to Z=33.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø78.1 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø63.2 mm over length 5.0 mm (from Z=0.0 to Z=69.1).\n9. Finish turn diameter Ø53.6 mm over length 29.4 mm (from Z=0.0 to Z=64.1).\n10. Finish turn diameter Ø47.2 mm over length 34.7 mm (from Z=0.0 to Z=34.7).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00654
|
[
"images/Shaft_00654.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø32.0 mm and length at least 159.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø30.0 mm over length 100.1 mm (from Z=0.0 to Z=100.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø30.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø23.6 mm over length 54.5 mm (from Z=0.0 to Z=54.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_00399
|
[
"images/Shaft_00399.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø52.2 mm and length at least 211.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.2 mm over length 72.9 mm (from Z=0.0 to Z=72.9).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.3 mm over length 67.1 mm (from Z=0.0 to Z=133.9).\n10. Finish turn diameter Ø30.0 mm over length 66.8 mm (from Z=0.0 to Z=66.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00504
|
[
"images/Shaft_00504.png",
"detail_png/Shaft_00504_length.png",
"detail_png/Shaft_00504_diam.png",
"detail_png/Shaft_00504_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø45.2 mm and length at least 283.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø43.2 mm over length 79.1 mm (from Z=0.0 to Z=79.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø43.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 199.4 mm (from Z=0.0 to Z=199.4).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_02528
|
[
"images/Shaft_02528.png",
"detail_png/Shaft_02528_length.png",
"detail_png/Shaft_02528_diam.png",
"detail_png/Shaft_02528_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø76.9 mm and length at least 303.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø74.9 mm over length 69.7 mm (from Z=0.0 to Z=69.7).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø74.9 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø67.6 mm over length 46.2 mm (from Z=0.0 to Z=228.3).\n10. Finish turn diameter Ø62.2 mm over length 57.2 mm (from Z=0.0 to Z=182.1).\n11. Finish turn diameter Ø50.7 mm over length 16.3 mm (from Z=0.0 to Z=124.9).\n12. Finish turn diameter Ø43.1 mm over length 37.3 mm (from Z=0.0 to Z=108.6).\n13. Finish turn diameter Ø30.4 mm over length 71.3 mm (from Z=0.0 to Z=71.3).\n14. Break all edges (e.g., 2×45° where applicable).\n15. Remove the workpiece from the lathe."
}
] |
Shaft_04205
|
[
"images/Shaft_04205.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø49.7 mm and length at least 85.7 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø47.7 mm over length 13.4 mm (from Z=0.0 to Z=13.4).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø47.7 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø40.5 mm over length 17.7 mm (from Z=0.0 to Z=67.3).\n9. Finish turn diameter Ø37.1 mm over length 24.4 mm (from Z=0.0 to Z=49.6).\n10. Finish turn diameter Ø31.3 mm over length 25.2 mm (from Z=0.0 to Z=25.2).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_01592
|
[
"images/Shaft_01592.png",
"detail_png/Shaft_01592_length.png",
"detail_png/Shaft_01592_diam.png",
"detail_png/Shaft_01592_title.png"
] |
[
{
"from": "user",
"value": "<image>\n<image>\n<image>\n<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø52.5 mm and length at least 253.0 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø50.5 mm over length 29.0 mm (from Z=0.0 to Z=29.0).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø50.5 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø38.4 mm over length 131.4 mm (from Z=0.0 to Z=219.0).\n10. Finish turn diameter Ø30.0 mm over length 87.6 mm (from Z=0.0 to Z=87.6).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_00209
|
[
"images/Shaft_00209.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material C45) with diameter at least Ø65.9 mm and length at least 122.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø63.9 mm over length 45.6 mm (from Z=0.0 to Z=45.6).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø63.9 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø51.4 mm over length 55.5 mm (from Z=0.0 to Z=72.3).\n9. Finish turn diameter Ø32.7 mm over length 16.8 mm (from Z=0.0 to Z=16.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04549
|
[
"images/Shaft_04549.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a aluminium alloy round bar (material EN AW-6082) with diameter at least Ø55.0 mm and length at least 146.5 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø53.0 mm over length 24.1 mm (from Z=0.0 to Z=24.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø53.0 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø36.0 mm over length 25.0 mm (from Z=0.0 to Z=117.4).\n10. Finish turn diameter Ø30.0 mm over length 92.4 mm (from Z=0.0 to Z=92.4).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
Shaft_04292
|
[
"images/Shaft_04292.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø40.2 mm and length at least 151.9 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø38.2 mm over length 11.8 mm (from Z=0.0 to Z=11.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø38.2 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 135.1 mm (from Z=0.0 to Z=135.1).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_01829
|
[
"images/Shaft_01829.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 42CrMo4) with diameter at least Ø37.6 mm and length at least 152.6 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø35.6 mm over length 20.8 mm (from Z=0.0 to Z=20.8).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø35.6 mm.\n6. Face the end and set Z=0.\n7. Center-drill the free end and support the bar with tail support.\n8. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n9. Finish turn diameter Ø30.0 mm over length 126.8 mm (from Z=0.0 to Z=126.8).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_03767
|
[
"images/Shaft_03767.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a stainless steel round bar (material 1.4301) with diameter at least Ø69.3 mm and length at least 67.1 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø67.3 mm over length 19.2 mm (from Z=0.0 to Z=19.2).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø67.3 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø47.5 mm over length 12.4 mm (from Z=0.0 to Z=42.9).\n9. Finish turn diameter Ø35.1 mm over length 30.5 mm (from Z=0.0 to Z=30.5).\n10. Break all edges (e.g., 2×45° where applicable).\n11. Remove the workpiece from the lathe."
}
] |
Shaft_04463
|
[
"images/Shaft_04463.png"
] |
[
{
"from": "user",
"value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."
},
{
"from": "assistant",
"value": "1. Select a steel round bar (material 16MnCr5) with diameter at least Ø79.4 mm and length at least 120.8 mm to allow machining allowances.\n2. Mount the bar in a three-jaw chuck.\n3. Face the end.\n4. Finish turn the holding diameter Ø77.4 mm over length 36.1 mm (from Z=0.0 to Z=36.1).\n5. Mount the bar in a three-jaw chuck by the holding diameter Ø77.4 mm.\n6. Face the end and set Z=0.\n7. Rough turn the remaining outer surfaces leaving ~0.5–1.0 mm stock per side for finishing.\n8. Finish turn diameter Ø64.9 mm over length 33.0 mm (from Z=0.0 to Z=79.7).\n9. Finish turn diameter Ø57.9 mm over length 27.9 mm (from Z=0.0 to Z=46.7).\n10. Finish turn diameter Ø46.1 mm over length 18.8 mm (from Z=0.0 to Z=18.8).\n11. Break all edges (e.g., 2×45° where applicable).\n12. Remove the workpiece from the lathe."
}
] |
End of preview. Expand
in Data Studio
Shaft Dataset (70/30 single vs multi-image)
Tento dataset vznikl automaticky z generovaných výkresů hřídelí.
Počet záznamů (po spárování): 5000
Obrázky:
images/Shaft_XXXXX.png— celý výkres (export přes Inkscape)detail_png/Shaft_XXXXX_length.png— výřez délkových kótdetail_png/Shaft_XXXXX_diam.png— výřez průměrových kótdetail_png/Shaft_XXXXX_title.png— výřez popisového pole
Mix: cca 70 % má 1 obrázek, cca 30 % má 4 obrázky
Formát JSONL
Každý řádek:
{
"id": "Shaft_01234",
"images": ["images/Shaft_01234.png"],
"conversations": [
{"from": "user", "value": "<image>\nGenerate the machining process for the shaft in the image. Use the exact 10–11 step template."},
{"from": "assistant", "value": "1. ...\n2. ..."}
]
}
Split
- train: 89%
- val: 5%
- test: 5%
- Downloads last month
- 46